Why Your LG Washer Has an IE Error Code + Quick Fixes

I’ve researched and experienced plenty of issues with appliances.

One of the most common problems I’ve come across is the infamous ie error code lg washer.

This error can be a real headache, but with the right knowledge, you can get your washing machine back up and running in no time.

I’ll walk you through the potential causes and step-by-step solutions to help you tackle this problem head-on.

By the end of this, you’ll be a pro at diagnosing and fixing the ie error code lg washer.

No more frustration, just a clean, functioning machine.

Key Takeaways

• Common causes of the IE error code on LG washers include water supply issues, clogged filters, and incorrect drain hose positioning.
• Solutions involve checking water connections, cleaning filters, and ensuring proper hose placement.
• If the error persists after troubleshooting, the control board or other components may need inspection or replacement.

Main Causes and Solutions for IE Error Code LG Washer

Cause 1: Water Supply Taps are Turned Off or Not Fully Open

Problem: Water taps are not fully open.

We’ve had this problem before, and that darn water usually causes its taps not to be open all the way.

You know, the ones behind the washer? If they ain’t turned on fully, it messes up the water flow and triggers that annoying IE error code.

Here’s what we gotta do to fix it:

Solution: Check both hot and cold water taps behind the washer. Turn them counterclockwise as far as they can go.

Once those taps open up well, let’s try running a wash cycle again. That should do the trick and get rid of that pesky IE error.

Cause 2: Incorrect or Incompatible Water Supply Hoses

We’ve seen this a lot, and it’s often cuz of the wrong hoses. You know, those “FloodSafe” ones from other brands? They don’t always play nice with LG’s inlet valves.

Problem: Using incompatible or incorrect water supply hoses.

Here’s what we gotta do:

Solution: Replace non-LG hoses with LG-compatible ones. Ensure they are tightly connected.

Take a look at your hoses. If they ain’t LG, that’s probably our culprit.

Note: Make sure you connect the flat end to the water tap and curved end to the washing machine inlet.

Check whether both extremities of the hose have a rubber seal in place to prevent water leaks.

Get yourself some proper LG hoses. They’re made to work with your machine.

Hook them up well and tight to both the taps and the washer.

Turn those taps on full blast and give it a go!

We’ve fixed tons of these, and swapping out the hoses usually does the trick.

It’ll let your washer fill up right without throwing that annoying IE code at ya. 

Trust me, we’ve been there, and this fix works like a charm most of the time.

Cause 3: Damaged or Kinked Water Supply Hoses

If ya water hoses are messed up or have kinks, it can mess with the water flow to your washer, and boom – you get that annoying IE error code.

Problem: Hoses are damaged or kinked.

Here’s what we can do to fix it:

Solution: Inspect hoses for cracks or kinks. Replace damaged hoses and straighten out any kinks before reconnecting.

1. Then we gotta take off the hoses from both ends – the washer and the taps.
2. Give them a good look-see for any cracks or holes. If they’re busted, we’ll need new ones.
3. But if they’re just kinked up, we can try straightening them out real careful-like. When we put them back, make sure we don’t bend them too much.
4. Once we get the hoses sorted, let’s hook them back up nicely and tight. Don’t want any leaks! Then we turn the water back on and plug in the washer.

Let’s run a test wash and see if that pesky IE code is gone. If it’s still there, well, we might have a different problem on our hands.

Cause 4: Blocked Water Inlet Filters

We’ve had this problem with our LG washer – those water inlet filters on the back can get all gunked up, and then you get that annoying IE error cause not enough water’s getting in.

Problem: Filters are clogged.

Here’s how we fixed it:

Solution: Turn off the water and disconnect the hoses. Remove and clean the filters, then reattach the hoses.

First, ya gotta turn off the water in the washer. Then unplug the hoses from the back.

Use some pliers to pull out the little filters in the inlet valves. Give them a good scrub under the tap – an old toothbrush works great for getting all the gunk off.

Once they’re clean, stick them back in and hook up the hoses again. Turn the water back on and try running a load.

It’s not too hard once you know what you’re doing. We were surprised at how much crud had built up in ours! Hopefully, that’ll sort out that IE error for you too.

Cause 5: Frozen Water Lines

If our water lines or faucets freeze up cuz of cold weather, the washer won’t fill right and we’ll get that annoying IE error code.

Problem: Water lines or faucets are frozen.

Here’s how we can fix frozen water lines:

Solution: Thaw out frozen faucets and hoses using warm water or a hot towel.

Take off the hose from the washer.

Turn on the faucet and see if any water comes out. If it doesn’t, it’s probably frozen.

Wrap a hot wet towel around the faucet for like 5 minutes to thaw it out.

To thaw the hose we took off, run some warm water over it (not hotter than 50°C) til all the ice is gone.

Once everything’s thawed out well, put the hose back on the washer.

Cause 6: Incorrect Drain Hose Positioning

We’ve been dealing with this IE error on our LG washing machine, and it’s all cuz of the drain hose! Turns out, if you put it too deep in the pipe, it messes everything up.

Problem: Drain hose is inserted too deeply into the pipe.

Solution: Position the drain hose 8-10 inches into the drain pipe to prevent siphoning.

Here’s what we did to fix it:

we found where the hose connects to the washer.

We saw it was way too far in the drain pipe, so we pulled it out a bit. You want it like 8-10 inches from the pipe, not all the way in.

We made sure it wasn’t siphoning. If it’s too deep, it can suck water out and mess up the filling.

Cause 7: Water Pressure Issues

It’s usually because of low water pressure from the supply lines. Your washer’s just not getting enough water fast enough, you know?

Problem: Low water pressure.

Solution: Check household water pressure. If low, consider installing a pressure booster pump or consult a plumber.

Here’s what we can try to fix it:

Check your water pressure. Most LG washers need about 20 psi (138 kPa), but yours might differ.

If the pressure’s low all over your house, try turning on some other faucets to see.

If it’s just the washer acting up, take a look at the hoses. Any kinks or cracks? Might need to swap them out.

Still not working? Maybe we need to install one of the pressure booster pumps. It’ll give your washer the extra oomph it needs.

If all else fails, we might need to call in the big guns – a plumber. They can check if there’s something funky going on with your main water supply. 

How do I clear the error code on my LG washer?

Oh man, dealing with an error code on your LG washer can be a real headache, right? But don’t worry, I’m here to help you figure it out. First off, let’s address that pesky ie error message.

This usually pops up when your washer is having trouble getting enough water. 

So, the first thing you want to do is check the water pressure.

Head over to where the hose connected to the washing machine hooks up and make sure the connections are tight and there are no kinks that might cause a block.

If that doesn’t work, it’s time to dive a bit deeper. You should also check the water supply itself—sometimes, it’s as simple as turning a valve all the way to open, you know?

There’s also the chance that foreign objects are messing with the water flow either in the supply hose from the washing machine or even in the water pipe.

Checking for any kind of pinch in the hose from the washing machine can also sometimes do the trick.

Oh, and while you’re at it, examine the filter of your front load washing machine; sometimes foreign objects get stuck and restrict water flow, causing that dreaded error code to appear.

Now, if your LG washer uses LG direct drive technology, things might be slightly different but the concept is the same.

If you’ve gone through all these steps and that annoying inlet error is still ruining your laundry day, you might need to head over to the LG site and check out their help library.

They have a ton of useful info that can guide you through various fixes. If DIY isn’t cutting it and the error code will appear again and again, you might want to contact us section on the LG site for more expert advice.

They often suggest cleaning the tub or checking other home appliances like the LG dishwasher to see if there are broader water supply issues in your home.

In summary, dealing with error codes on your LG front load washer—or any LG front load washing machine—involves a few basic checks: make sure your water connections are tight, the pressure is sufficient, and there are no foreign objects in the supply lines.

Sometimes, the error code appears simply because of minor issues that are easy to overlook. 

FAQs