How To Take Out Frigidaire Water Filter

Are you wondering how to take out Frigidaire water filter? I’ve got you covered.

Changing your fridge filter is easier than you might think; you can replace the water filter in your Frigidaire refrigerator in just a few minutes.

I’ve researched and experienced this process firsthand.

Clean water is crucial for your health and your appliance’s longevity. A fresh filter ensures your ice and water taste great, especially when using a Frigidaire Gallery refrigerator.

In this guide, I’ll walk you through the steps to replace your Frigidaire filter. Get ready to improve your water quality in just a few minutes!

Key Takeaways

Replace filter every 6 months
Filter location varies by model
Turn off ice maker before replacement
Flush new filter with 2 gallons of water
Reset filter indicator after installation

Content on The Page

How To Take Out Frigidaire Water Filter – Guide

1. Turn Off the Ice Maker

Before starting, it’s advisable to turn off the ice maker to prevent any ice from being produced during the filter change. This can usually be done by pressing the ice maker button on the control panel.

2. Locate the Water Filter

The water filter is typically located in one of the following areas, depending on your refrigerator model:

Top Right Corner; you will often find the water filter in your Frigidaire refrigerator located here on the refrigerator compartment for many models.
Inside the grille, you may find the water filter on your Frigidaire refrigerator, which is essential for clean drinking water at the bottom front of the refrigerator.

3. Remove the Old Filter

For Push-Button Eject Filters (e.g., WF2CB), you can watch a helpful video on how to change the water filter effectively:

Push the eject button to release the refrigerator water filter.
Pull the refrigerator water filter straight out of the housing.

For Eject-and-Slide Filters (e.g., ULTRAWF):

Open the filter cover door.
Pull the filter out of the housing.

For Twist-to-Remove Filters (e.g., EPTWFU01):

Twist the filter to the left and pull it out.

For Cup Filters in your Frigidaire refrigerator (e.g., WFCB), make sure to check the expiration date to know when to change the water filter:

Twist the filter cover cup to the left and remove it; this step is crucial for replacing the water filter in your Frigidaire refrigerator.
Pull the filter out of the housing.

4. Prepare the New Filter

Take the new filter out of the box and peel off any cover caps. Once the cover caps are removed, check the filter for any damage that may have occurred during shipping.

Ensure that the O-rings are properly seated and lubricated if necessary.

Next, locate the filter housing on your appliance and carefully open it, following any specific instructions provided by the expert manufacturer.

5. Install the New Filter

For Push-Button Eject Filters:

Insert the new filter into the housing and push until it clicks into place. Make sure the filter is securely positioned by gently pulling on it to check that it doesn’t move.

Image of checking the housing of water filter

Once confirmed, you can replace the housing cover and secure it by tightening any screws or turning any locking mechanisms as needed.

For Eject-and-Slide Filters:

Align the filter with the housing and slide it in until it stops. Ensure that the filter is properly seated by pressing it gently but firmly into place. You should feel it click or fit snugly without any gaps.

For Twist-to-Remove Filters:

Insert the new filter and twist it to the right until it locks into place; this ensures the water filter in your Frigidaire is securely installed.

Once the new filter is securely locked into place, it’s important to flush the filter to remove any air and impurities.

To do this, run water through the dispenser for about 3 to 4 minutes, or until the water runs clear.

For Cup Filters:

Insert the new filter into the housing with the nozzle pointing up and reinstall the filter cover to ensure proper filtration in your side by side refrigerator.

6. Prime the New Filter

Image of placing the prime the New Filter

Run about 2 gallons of water through the dispenser to purge air and any residual contaminants from the new filter. This step is crucial for ensuring the filter works effectively.

7. Reset the Water Filter Indicator

If your refrigerator has a water filter replacement indicator, reset it according to your model’s instructions, usually by pressing and holding the reset button for a few seconds; this is important for the water dispenser to function properly.

FAQs

How often should I replace the water filter in my Frigidaire?

It’s recommended to replace the water filter in your Frigidaire every six months. This helps ensure you’re getting nothing but crystal clean water and ice.

Where is the water filter in my Frigidaire located?

The location of the water filter can vary by model. Typically, you can find it either inside the fridge compartment or in the grille at the bottom, especially if you own a French door refrigerator.

What tools do I need for the water filter removal?

Good news! You generally won’t need any special tools for the removal process. Just your hands and a bit of twist and pull action will do the trick.

How do I know which Frigidaire water filter I need?

Use the filter finder tool on the Frigidaire website. It helps you determine which water filter model fits your fridge, ensuring you’re always providing fresh drinking water.

What should I do if water tastes funny after changing the filter?

It’s common for the water to taste a bit odd right after changing the filter. Run a few gallons of water through the new filter to flush out any residues. You should then enjoy crystal clean water.

Do I need to turn off the water supply before removing the filter?

Most Frigidaire models don’t require you to turn off the water supply before removing the filter. Check your fridge’s manual for specific instructions.